PCTuning fórum

smht píše:Hlavne chladiť tým gpu aj CPU asik nic moc pri danom rade, veľký rozdiel tam asik nebude oproti teplotám ako máš teraz. Pripadne ma kľudne opravte

MaWa píše:Ono s těma úhlovkama - není problém vyrobit úhlovku, které nová nepoteče. Je problém vyrobit úhlovku, která nepoteče ani když po pěti letech vypustíš okruh, protočíš je a okruh znova napustíš. Tam se láme chleba. Ty těsnění vevnitř zatvrdnou v jedné poloze, "tlak" vody v okruhu to utěsní, takže i když těsnění už dávno je tvrdé jak beton, tak to nezačne téct. Ale opravdu ve chvíli kdy se na tom PC udělá nějaký servis (výměna kapaliny nebo nějaké předělání chlazení) tak tam se pozná kvalitní úhlovka a šmejd. Například proto před mnoha lety EKWB ukončilo jejich EK-PSC úhlovky - protože přesně tenhle problém měly. Po mnoha letech v okruhu a vypuštění PC a otočení s nimi teklo po opětovném napuštění okruhu tak 9 kusů z 10 a to beze srandy. Přitom z výroby byly úplně v pohodě, poruchovost nula. Pokud stejný postup uděláš s úhlovkami Alphacool nebo XSPC, potečou tak 3 z 10. Pokud stejný postup uděláš s úhlovkami Bitspower, poteče ti jedna ze sta. Jak jsou na tom třeba EKWB AF řada a třeba Alphacool Eiszapfen je zatím těžko říct, ještě nejsou na trhu dost dlouho, teprve cca 3 roky a takovou dobu vydrží i šmejd z číny za dolar kus. Takže tvrdit, že Bykski úhlovky jsou super je docela odvážné tvrzení, to se dozvíme tak za 5 let, jestli je to šmejd nebo OK nebo něco mezi tím.

Quite a bit of people think that Barrow fittings are made by Bitspower just without the logo but that is far from the true. BP doesn't have copyright on their products so not much they can do. From lengthily conversations I had with BP, they don't seem to really care . Barrow is thief of copy Bitspower product but the quality and material they use is cheap and users purchasing Barrow products sooner or later can discover that for themselves.

You can copy all you want and on the surface might look quite good to an average person until you start using them. Barrow uses brass which is copper and zinc rather than pure copper, they use O-rings that are made out of cheep rubber, I'm not sure what is made of but they tear very easy and when you tighten them in your system, you have to go all the way until you cannot go any further otherwise most likely they will leak down the road like they did for my Nephew despite they were very tight fit.

Also, if you get something like Black Matte or dark finish it comes off like crazy, maybe not at first and that is strange but giving a bit time their coating comes off very easy.

I won’t mention name, but another company who is, actually was selling Barrow fittings in Germany just dropped them due to several issues with many people that are complaining about leaks and none consistent tolerance in fit, some are way small some bigger.
People who appreciate quality knows the difference between org. and fraudulent copy products and when you hear or see something that might be to good to be true....well most of the times is bad

Bitspower fittings can last very long time if not life time if you use proper liquid and don't abuse them during install. People don't realize that there is more to quality then just copy something to make it look similar to well knowing superior brand(s)

90% of these fittings are 10 years old and older but they look like the day I got them and they have been in so many different builds

https://www.overclock.net/forum/attachm ... 1546240306
https://www.overclock.net/forum/attachm ... 1546240306
https://www.overclock.net/forum/attachm ... 1546240306
https://www.overclock.net/forum/attachm ... 1546240306

Loki5567 píše:Už se dá koupit ten Cryofuel u tebe koupit MaWa ? vypadá to jako docela slušně že bych si ji lupnul do buildu s BykSki