Stránka 4 z 4

Napsal: úte 25. črc 2006, 15:13
od Jája
3/8" - tři osminy palce - palec je 25,4mm => potřebuješ hadice s vnitřním průměrem 9,525mm, můžeš použít i o trochu menší, záleží jak moc jsou pružný tedy o kolik sedají roztáhnout - pak to tam víc drží a nemusíš je stahovat.

Napsal: úte 25. črc 2006, 17:50
od wector
sejny píše:
wector píše: To by mě zajímalo, jak je to v reálu. Ta 1048 tam hučí dost hlasitě, ale když ji hodí do compu na něco měkkýho, tak o ní nevíš...
hlasitostí se nemůžeš vůbec řídit, podle tohodle můžeš jen porovnávat mezi sebou
O to nejde, zajímá mě faktická hlučnost. Asi pudu do ní, D5 je ku~evsky drahḠDDC by nemusela stačit { plánuju brzo 2-3 radiátory :oops: }. Uvidim, nejdřív musej dorazit prachy za HPPSko a až se vrátim home¸ tak to dořešim. Docela dost je v cizině oblíbena značka Iwaki, znáte někdo?

Napsal: úte 25. črc 2006, 18:18
od Cujo
shrnuti z recenze DDC (prelozeno z DE do ENG)
The Laing DDC states our Charts in all categories before the AP1500. Which the pressure concerns is decisively superior it the competition pumps in the wahrsten sense of the word. Here we should deal perhaps still with the fact that the pump is really tiny compared with all other pumps, which we tested ever here. The actual pump is still smaller than the Plexi cover. If one the latches with takes into consideration has it the mass of 90*60*20 (L*B*H). Compared with a Eheim 1048 or a Hydor L30 that is not nothing at all. Likewise in the current consumption it is extremely reserved. In the 12-V-Betrieb she is satisfied with only 0,8 A (9.6 W). If one considers the results of measurement, then this is amazingly smaller and just as pleasing value. The high approach value, that on over 4 A is only endowed clouds the picture somewhat. Evenly those approach problems were to be recalled in the past reason for it a majority of the pumps again. After a change of the firmware the problem is to be however repaired. Now still another last point: The volume. The Laing lies completely far in front also here. Compared with a AP1500 and their surrendem power pack almost is it dead quiet. Humming was not to be heard at all, however a quiet Surren. This is however absolutely justifiable, and if one is distant from the pump further as 20 cm, also not more perceptibly. It from the inside of a PC housing to hear out, is impossible. Our result: The Laing DDC is clearly the pump of the future. It combines achievement at minimalistic place, is quiet and economizes well with river. There actually no more desires remain openly. The price of scarcely 90?, it with Cooling Solutions including the cover costs, is of course somewhat happig and bad with the 42?, some Eheim 1046 costs comparably, but just as little the two pumps are comparable with one another. Between them worlds lie. Alternatively does one know also the normal version of the DDC pump without Plexi covers for 75? acquire. This time we go stating really so far that the Laing DDC with distance is the best pump, which we tested ever.
co se tyce D4ky, tak hlucnost je jedine ceho se u ni bojim
mozna trochu vibrace, ale to se da osefovat

Napsal: úte 25. črc 2006, 18:37
od pEeLL
Jája píše:3/8" - tři osminy palce - palec je 25,4mm => potřebuješ hadice s vnitřním průměrem 9,525mm, můžeš použít i o trochu menší, záleží jak moc jsou pružný tedy o kolik sedají roztáhnout - pak to tam víc drží a nemusíš je stahovat.
tak presne tohle jsem potreboval vedet :D diky moc.

Napsal: úte 25. črc 2006, 18:47
od wector
Cujo píše:shrnuti z recenze DDC
Datum tý receze?

haďyc :)

Napsal: úte 25. črc 2006, 19:20
od pEeLL
tak koukam na gumex

http://www.gumex.cz/cz/katalog_detail.p ... ina=1&fcc=

lidi ktere hadicky s vnitrnim prumerem 10mm ??? predpokladam ze se ma vybirat asi podle tlaku - ale kolik baru potrebuju k laing ddc??

logicky si myslim ze bohate staci i ty nejobycejnejsi ale raci se zeptam.

Obj. kód Průměr (mm) Pracovní tlak-vzduch (bar) Pracovní tlak-voda (bar) Poruchový tlak (bar) Poloměr ohybu (R.min.-mm) Hmotnost (kg) Balení (info) Měrná jednotka Cena (Kč)*
0001010 10/14 6 10 32 120 0,12 50 m 13,8

Napsal: úte 25. črc 2006, 20:50
od sejny
jasně že Ti stačí třebas silikon 10/14... jednou jsem dělal takový pokus se slilikonovou hadičkou a kompresorem z ledničky: kus hadičky jsem napojil na výtlak a druhý konec zaslepil, po zapnutí kompresoru měla hadička aspoň 6x větší průměr a držela :twisted: tak jsem to nechal dokud nebouchne...takže, pokud se hadice nebudou nafukovat, neřeš to, samo je musíš mít dobře zaponkovaný aby někde nemohla nějaká slézt