Bengo píše:Mam pridat pametem napeti? Jsou to ddr2 1.8 V. Ted je pridano +4. To bude asi + 0.4 V
napiš nejdřív přesně konfiguraci a pak jak to máš v biosu nastavený (alespoň ty červené označené) a pak je možné s tím trochu něco dělat, takhle je to vaření z vody..... a až to dáš dohromady, tak pokud mohu doporučit tak zkontaktuj uživatele "Lokomotiva" je to na přetaktování machr
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................:
8x
Fine CPU Clock Ratio.....................:.
+0.0x
CPU Frequency ...........................:
2,xxGhz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:
400
PCI Express Frequency (Mhz) .........: [100]
C.I.A.2 .................................: [Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: [700]
PCI Express Clock Drive.................: [700]
CPU Clock Skew (ps)....................: [ 0ps]
MCH Clock Skew (ps)...................: [ 0ps]
DRAM Performance Control
Performance Enhance...................:
[standart]
(G)MCH Frequency Latch...............:
[400Mhz]
System Memory Multiplier ..............:
[2.00D]
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................
5
tRCD .........................................
5
tRP'...........................................
5
tRAS..........................................
15
Advanced Timing Control
tRRD......................................3... [Auto]
tWTR......................................3... [Auto]
tWR.......................................6... [Auto]
tRFC......................................52.. [Auto]
tRTP......................................3... [Auto]
Command Rate (CMD) .......................0... [Auto]
Channel A
Static tRead Value........................9.. [Auto]
tRD Phase0 Adjustment.....................0... [Auto]
tRD Phase1 Adjustment.....................0... [Auto]
tRD Phase2 Adjustment ....................0... [Auto]
tRD Phase3 Adjustment.....................0... [Auto]
Trd2rd(Different Rank)....................6... [Auto]
Twr2wr(Different Rank)....................6... [Auto]
Twr2rd(Different Rank)....................5... [Auto]
Trd2wr(Same/Diff Rank)....................8... [Auto]
Dimm1 Clock Skew Control...................... [Auto]
Dimm2 Clock Skew Control...................... [Auto]
DDR Write Training ........................... [Auto]
Channel B - stejné jako A
Motherboard Voltage Control
CPU
CPU Vcore .......................1.28750V...
[1.325]
CPU Termination .................1.200V.....
[Auto]
CPU PLL .........................1.500V.....
[Auto]
CPU Referen .....................0.760V..... [Auto]
CPU Reference2 ..................0.800V..... [Auto]
MCH/ICH
MCH Core ........................1.100V.........
[1.200]
MCH Reference ...................0.760V.........[Auto]
MCH/DRAM Ref ....................0.900V.........[Auto]
ICH I/O .........................1.500V.........[Auto]
ICH Core ........................1.100V.........
[1.200]
DRAM
DRAM Voltage ...................1.800V.........
[2.000V]
DRAM Termination ................0.900V.........[Auto]
Channel A Reference .............0.900V.........[Auto]
Channel B Reference .............0.900V.........[Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect .............. [Disabled]
ale přeci když jsou paměti 400MZH - ový, tak nemlžou při 414 padat ne ?
