Table 2: Connection Ports
Factory Default Settings
Setting
Wireless Access Point
Device Name
WL-5460AP v2
SSID
Default value: airlive
Channel
13
WEP
Default value: Disabled
IP Address
192.168.100. 252
DHCP Server
Enable
DHCP Server IP Range
192.168.100.100~192.168.100.200
HARDWARE CONNECTION
Note: Before you starting hardware connection, you are advised to find an appropriate location to place the
Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of
straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is
placed, the better will be the performance.
1. Connect to your local area network: connect a Ethernet cable to one of the Ethernet port
(LAN1 or LAN2) of this Wireless Access Point, and the other end to a hub, switch, router, or another
wireless access point.
2. Power on the device: connect the included AC power adapter to the Wireless Access Point’s power port
and the other end to a wall outlet.
Check the LEDs:
The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is traffic.
The Link/Act LED will be on in static when associated with a station and blink whenever this AP receives data
packets in the air.
If the Status LED glows after self-test , it means this Wireless Access Point fails on self test. Please ask
your dealer for technical support.
3. Configure your PC: Make sure your local PC(s) has wireless network adapter installed.
ABOUT THE WIRELESS OPERATION MODES
jsem vynechal stejne jako uvodni kecy
order to perform more advanced configuration or even change the mode of operation, you can use
the web-based utility provided by the manufacturer as described in the following sections.
CONFIGURATION
Login
1. Start your computer. Connect an Ethernet cable between your computer and the Wireless
Access Point.
2. Make sure your wired station is set to the same subnet as the Wireless Access Point, i.e.
192.168.100.252
3. Start your WEB browser. In the Address box, enter the following:
http://192.168.100.252
The configuration menu is divided into four categories:
Mode, Status, TCP/IP, and Other .
Click on the desired setup item to expand the page in the main navigation page. The setup
pages covered in this utility are described below.
Mode
You can choose and setup different wireless mode and for detail configurations
Alias Name You can s
LAN Inter
won’t be able to make wireless connection with this Access Point
network you are l
nd
any wireless station.
You can choose one mode of the following you need.
.. 2.4GHz (B): 802.11b supported rate only.
.. 2.4GHz (G): 802.1
.. 2.4GHz (B+G): 802.11b supported rate and 802.11g supported rate.
The default is 2.4GHz (B+G) mode.
The SSID differentiates one WLAN from anoth
points and all devices attempting to connect to a specific WLAN must use
the same SSID. It is case-sensitive and
device will not be permitted to join the BSS unless it can provide the
unique SSID. An SSID is also referred to as a network name because
essentially it is a name that identifies a wireless network.
Allow user to set the channel manually or automatically.
If set channel manually, just select the channel you want to specify.
If “Auto” is selected, user can set the channel range to ha
Access Point automatically survey and choose the chann
situation for communication.
The number of channels supported depends on the region of this Access
Point. All stations communicating with the Access Point must use the same
channel.
Press the setup button for detail configurations
wWith Open System authentication, a wireless PC can join any network and receive any messages
that are not encrypted. With Shared Key authentication, only those PCs that possess the correct
authentication key can join the network. By default, IEEE 802.11 wireless devices opeOpen System network and None data encryption. If you want secure your wireless network
you need to setup wireless security related function to enable security network.
Security.. Authentication
Open system or Shared Key.
t.
If the Access Point is using Op
authentication mode. Shared Ke
can choose Open system , or one Shared Key authenticat
Encryption: WEP
If selected, you must set WEP key value
gits or 13 ASCII characters are needed if 128-bit WEP is used.
O
Authentication RADIUEnter the RADIUS Server IP address and Password pro
Enter the Accounting RA
You can select WE
Authentication RADIUS Server:
Enter the RADIUS Server IP address and Password provided by your ISPEnable Accounting :
Enter the Accounting RAD
n this page, you
hange the TCP/IP settings of this Access Point, select to enable
HCP Client, 802.
panning Tree, and Clone MAC Address.
P Address
This field can be modified only when DH
system manager assigned you static IP se
ubnet Mask
efault
Enter the information provided by your syst
ateway
HCP
Select Disable, Client or Server from the pull-down menu.
Disable: Select to
Client: Select to automatically get th
ADSL/Cable Modem).
Server: Select to
WL-5060AP IP addresses continuing from 192.168.100.1 to
192.168.100.253
how Client
Click to show Active DHCP Client table.
Enter the Domain
802.1d
Spanning
Clone MAC You ca
file name (
IRMWARE\firmware.bin). Or, click the Browse button, find and open
e browser will display to correct file path).
the settings on this page. Or click
Reboot
Click the re
evice.
Other
d
screen will prompt you
a dialog box to enter the file name and the file location.
Load Settings F
File: Click Browse… if you want to load a pre-
name w
path and then click on Upload. Or click Browse… to select the file.
.