PCTuning fórum

v cem je problem nejde o prave verbatimy nebo jde o spatnou serii u kazdeho dvd se narazil na to sami pres dvd identifier.

mam to reklamovat

a sorry ze to nedavam do sekce reklamace nevim zda-li se jedna o reklamaci

Co je to za verbatimky? + nebo -? Zkoušels nějaké pálit?

jde o dvd+r

co je ta metoda 1 a metoda 2?

mam novy firmware u lg h10n JL12

nejedna se o nejaky podvrh jak to poznat

jedna se jak o reorder 43507 tak to sami je u 43497

dvd+r reorder 43507 MCC
[DVD+R:MCC-004-000]


vypaleno 8x a vse v poradku pri vypalovani a pri verifikaci.


** INFO : Drive = HL-DT-ST DVDRAM GSA-H10N - [FW JL12] - [ATAPI]
** INFO : Write Capabilities = DVD+R DVD+R-DL DVD+RW
** INFO : Write Capabilities = DVD-R DVD-R-DL DVD-RW DVD-RAM
** INFO : Disc = [DVD+R:MCC-004-000]
** INFO : Reference Speed : 1x DVD = 1385 kBps
** INFO : An Writeable Disc Is Recommended For Accurate Results
** INFO : Write Speeds (Supported By This Drive On This Disc) Listed Below

reorder 43449 dvd-ram tam je to take kdyz si zapnete dvd identifier ta sama
hlaska

nesetka se s tim u 43519

21.4.2007
ISO compilation
11:58:43 #1 Text 0 File Isodoc.cpp, Line 6172
Iso document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE

11:58:43 #2 Text 0 File Reader.cpp, Line 127
Reader running

11:58:43 #3 Text 0 File Writer.cpp, Line 122
Writer HL-DT-ST DVDRAM GSA-H10N running

11:58:43 #4 ISO9660GEN -11 File geniso.cpp, Line 3293
First writeable address = 0 (0x00000000)

11:58:43 #5 Text 0 File Burncd.cpp, Line 3153
Turn on Disc-At-Once, using DVD media

11:58:43 #6 Text 0 File DlgWaitCD.cpp, Line 259
Last possible write address on media: 2295103 (510:01.28, 4482MB)
Last address to be written: 1503135 (334:01.60, 2935MB)

11:58:43 #7 Text 0 File DlgWaitCD.cpp, Line 271
Write in overburning mode: NO (enabled: CD)

11:58:43 #8 Text 0 File DlgWaitCD.cpp, Line 2316
Recorder: HL-DT-ST DVDRAM GSA-H10N, Media type: DVD+R
Disc Manufacturer ID: MCC, Media Type ID: 004, Product revision number: 0
Disc Application Code: 0, Extended Information Indicators: 7

11:58:43 #9 Text 0 File DlgWaitCD.cpp, Line 433
>>> Protocol of DlgWaitCD activities: <<<
=========================================

11:58:43 #10 Text 0 File ThreadedTransferInterface.cpp, Line 830
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 1503136 (1503136) = #1503136/334:1.61
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 1503136 blocks [HL-DT-ST DVDRAM GSA-H10N]
--------------------------------------------------------------

11:58:43 #11 Text 0 File ThreadedTransferInterface.cpp, Line 1043
Prepare recorder [HL-DT-ST DVDRAM GSA-H10N] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 3078422528, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep__________
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
1503136 | lead-out | 1 | 0x41 | 0x00

11:58:44 #12 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

11:58:44 #13 Text 0 File Burncd.cpp, Line 4040
Cache writing successful.

11:58:44 #14 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

11:58:44 #15 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 8x (11 080 KB/s)

11:58:44 #16 Text 0 File ThreadedTransferInterface.cpp, Line 2609
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

11:58:44 #17 Text 0 File Cdrdrv.cpp, Line 8430
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD+R (10), Part Version: 1
Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 26053F h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Disc Application Code: 0 / 0 h
Extended Information indicators: 7 h
Disc Manufacturer ID: MCC.....
Media type ID: 004
Product revision number: 0
Number of Physical format information bytes in use in ADIP up to byte 63: 56
Media Specific [16..63]:
00 00 07 4D 43 43 00 00 - 00 00 00 30 30 34 00 38 ...MCC.....004.8
23 54 37 12 02 54 6C 02 - 92 5F 15 15 0B 0B 08 08 #T7..Tl.._......
01 19 1B 0C 0C 0C 0D 01 - 00 00 00 00 00 00 00 00 ................

11:58:44 #18 Text 0 File DVDPlusRW.cpp, Line 638
Start write address at LBA 0
DVD high compatibility mode: Yes

12:03:50 #19 Text 0 File WriterStatus.cpp, Line 116
<HL-DT-ST DVDRAM GSA-H10N > start writing Lead-Out at LBA 1503136 (16EFA0h), lenght 0 blocks

12:03:50 #20 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

12:04:13 #21 Phase 37 File dlgbrnst.cpp, Line 1832
Burn process completed successfully at 8x (11 080 KB/s)

12:04:13 #22 Phase 78 File dlgbrnst.cpp, Line 1832
Data verification started

12:04:17 #23 SCSI -1064 File Cdrdrv.cpp, Line 1181
SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x0012B2A4
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x21
Sense Qual: 0x00
CDB Data: 0xB6 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x1C 0x00
Sense Data: 0xF0 0x00 0x05 0x00 0x23 0x05 0x3F 0x10
0xB6 0x00 0x00 0x0E 0x21 0x00

12:07:52 #24 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

12:07:53 #25 Phase 80 File dlgbrnst.cpp, Line 1832
Data verification completed successfully


Existing drivers:
File 'Drivers\ASPI32.SYS': Ver=4.71 (0002), size=16877 bytes, created 17.7.2002 8:53:02
File 'Drivers\PXHELP20.SYS': Ver=3.00.33a, size=36528 bytes, created 25.8.2006 5:47:00 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 3.8.2004 23:59:44 (Adapter driver for rec)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

na jednom zahranicnim foru jsem videl od jednoho cloveka prispevek ktery rika ze lg vypalovacky a pouzite verbatimy vzdycky pokazde zobrazuji


ERROR : ADIP Read M1 Failed : Illegal request - Invalid field in CDB [05/24/00] v dvd identifier

ze je to zcela normalni mam tomu verit ci ne

The method 1 and 2 mentioned in DVD Identifier are used for identifying the disc. All LG burners use method 2 to identify DVD+R and it's normal to have the error message for method 1. They do not affect your burn results.

Have you tried playing the burned disc in your computer? What program did you use for burning? Did you check whether you have set the booktype correctly? Also, have you upgrade your 4163 to the latest firmware?

You can also visit the LG forum here for questions and answers.

odkazuje na lg forum ale zaboha nic nemohu najit

pise to jak u dvd-r tak dvd+r verbatim na vsech lg tu danou hlasku

error adip..........................

nejsem si tim zcela jisty ale kdyz tam byl predchozi firmware tak se mi tato hlaska nezobrazovala

soucasny firmware JL12 u LG H10N a predchozi JL11

Ta druhá metoda disk úspěšně identifikuje. Žádnej problém v tom nehledej.