K8N NEO a BIOS 1.6

[Dreath]

Zdarec všem, potřebuji radu ohledně přeflashování BIOSu Ver1.6 na zmíněné desce. Nedávno sem si ji koupil s BIOSem Ver1.5, pln očkávání sem si od výrobce stahl a následně flashl BIOS Ver1.6 a zjistil sem že to byla TOTÁLNÍ kravina. Sere mě na něm jedna věc a to že napětí CPU neni ve voltech ale v procentech s největší hodnotou 10%(1.51V max 2.21Ghz)- což je naprosto mrzácké vzhledem k tomu, že u kámoše (BIOS Ver1.3) mu to valí až na 1.8V a to na 2.4GHZ!!!! Takže sem chtěl opět flashovat a to na Ver1.3 (jistota je jistota) ovšem při flashování mě to vyhodilo chybu na spůsobu "máš zamknutý bios vole" a mlelo to jakésy kraviny o jumperech, což je hovadina protože při předchozím flashování mi to nic nedělalo a na desce žádné jumpery k tomuto účelu nejsou. Takže vás laskavě žádám o radu jestli s tímhle dílem máte někdo skušenosti a nevíte jak to "odemknout", neboli jak to flashnout z verze 1.6 na 1.3
Mnohokrát děkuji


//edit Wilik - presun ze s939 desek

[Shit]

Zkus flash s parametry: (před flashem zmáčkni v BIOSu "F7" a pak "F10".... restart a pak vlastní flash a pak znova "F7" a znova "F10")

Check them all .

Note : clearing DMI , ESCD/PNP data is important to reset/update .
(someone has surely heard about motherboards hanging in verifying dmi
after a flash)
Btw: this boards bios don't support "reset ESCD" so PNP option will not be
possible to mark.

Dos flash recommends :
AWFL833D W7030NMS.147 /py/sn/wb/cc/cd/cp/r

/WB - Updates the BIOS Boot Block. This switch does not have to be used. The BIOS Boot Block will get updated with the flashing of the BIOS.
Thanks for the input Tmod

/Py or /Pn - stands for answering "yes" (Y) or "no" (N) to the request concerning the BIOS reflashing. By means of /Pn you can ban FlashROM reprogramming. This option enables you to save the current version of the BIOS or to get its checksum without updating your BIOS. A backup copy will help you to restore the previous version of the BIOS. By default /Py mode is set.

/Sy or /Sn - stands for answering "yes" (Y) or "no" (N) to the request about saving the previous version of the BIOS. By default /Py mode is set again. In this case before reprogramming the FlashROM microchip you'll need to confirm saving by this request:

Do You Want To Save BIOS (Y/N)

/Sn is recommended to use for *.bat-files in case of automatic BIOS reflashing in systems without a display.

/CC - to clear CMOS after reflashing. This option comes in handy when there is a risk that the data arrays created by new BIOS version in CMOS may differ from those former ones. If so, then you are likely to have troubles with the mainboard startup. Clearing CMOS will let you avoid searching for Clear CMOS jumper on the board, which is really helpful if it isn't accompanied with a proper manual or is simply hard to access.

/CP - stands for clearing PnP (ESCD) Data matrix after BIOS reflashing. The information about PnP devices is stored in ESCD. The key /CP is an equivalent to Reset Configuration Data in PnP/PCI Configuration CMOS Setup. It makes sense to use /CP if you skip several versions of BIOS or if you have installed new PnP cards. If you don not update the ESCD, your board may suffer some startup problems.

/CD - stands for clearing DMI Data pool after reprogramming. Literally, DMI is a data base, containing all the information on the system as a whole. Clearing it may be fruitful in the above mentioned situations with /CP and /CC keys, as well as if some of the system components have been changed.

/R - stands for the system reset after reflashing. It lets you have your computer restarted automatically as soon as you finish updating FlashROM. The option is useful for working through a *.bat-file.

Using winflash make sure to check the corresponding options for a troublefree bios flash.



AWFL833D W7030NMS.151 /py/sn/wb/cc/cd/cp/r

Zdroj: fórum MSI

[Dreath]

No dík za informace ale mohl bys být trochu konkrétnější?? Víš pocházím z moravy a tam je ta mentalita tak trochu jiná.. Najel sem do BIOSu zmackl F7 a pak F10, restart, najel sem do teho flashovacího programu a ho*no. Takže sem asi udělal neco blbě

[Shit]

"F11" a zvol bootovací médium (disketka, CDR/CDRW, flashdisk..). Děláš to doufám z DOSu...

[mozeg]

v jednom z bios menu je polozka bios cacheble daj enable a uz ti to pojde